Quick Start
Brand (Aerogarden), model (100703). 100302-blk Aero Garden Aerogarden 3 System Works Great Bulb Not Included. The box and original packing material are included as well as user manual and other promotional literature, but the box is a little beat up. The cover has since been replaced. The pump does appear to work, but I have not tested. View and Download AeroGarden 100302-BLK quick start manual online. AeroGrow International, Inc. Indoor Greenhouse Kit Quick Start Guide. AeroGarden 100302-BLK Greenhouse Kit pdf manual download. Also for: 100302-bss, 100302-red, 100302-slr, 100302-wht, 3, 3 elite.
Guide
Simple Steps
To Get Your
Up and Growing
THIS | GUIDE! |
KEEP |
Model #s: 100610-BLK; 100610-WHT; 100610-SLR |
Date Code: |
Input Voltage: 120V, 60Hz, 1.5A |
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
When using this AeroGarden6 electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this AeroGarden furnishing.
1. To reduce the risk of electric shock, the AeroGarden has a specific plug. Do not change the plug in any way.
DANGER– to reduce risk of electric shock:
2. Always unplug AeroGarden from electrical outlet before cleaning or changing Grow Bulbs (light bulbs). WARNING– to reduce risk of burns, fire, electric shock, or injury to persons:
3.Unplug AeroGarden from outlet before putting on or taking off parts.
4.Close supervision is necessary when AeroGarden is used by or near children, invalids, or disabled persons.
5.Use AeroGarden only for its intended use as described in instructions. Do not use attachments not recommended by manufacturer.
6.Never operate AeroGarden if it has a damaged cord or plug, if it is not working properly, if it has been dropped and damaged, or if it has been dropped in water. If any of these conditions occur/exist, contact www.aerogardensupport.com or your country’s local distributor for instructions.
7.Keep cord away from heated surfaces.
8.Never operate furnishing with air openings blocked. Keep air openings free of lint, hair, and the like.
9.Never drop or insert any object into any electrical openings.
10.Do not use outdoors.
11.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12.Do not touch moving parts or hot parts such as pumps, bulbs, reflective surfaces, and the like.
13.To disconnect, remove plug from outlet.
14.Do not place or submerse base, cord, plug, or lamp hood in water or other liquid to clean it.
15.Do not allow water to contact hot light bulbs.
16.Use only approved and supplied parts and accessories. Use only lamp model 100340 (N. America) or 200340 (Europe & Australia) Grow Bulbs with this AeroGarden model. Use of any other kind of accessory is not recommended. Replacement parts can be ordered from www.aerogardensupport.com or from your retailer.
17.Do not use AeroGarden for other than intended purpose.
18.This product is intended for household and residential use only. This product is not approved for commercial applications.
19.Read and follow all important notices on the AeroGarden and in the accompanying literature.
20.If supply cord is damaged, it must be replaced by manufacturer, its service agent, or similarly qualified technician in order to avoid a hazard.
21.Electrical wiring must be in accordance with local regulations.
Aerogarden Manual User Guides
22.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of appliance by a person responsible for their safety.
23.Children should be supervised to ensure they do not play with the appliance.
Save These Instructions
A Unpack Your AeroGarden6
Lamp Hood
(front view)
Bowl
(front view)
Lamp Arm
(back view)
Base
(front view)
Seed Kit
Deluxe B Grow Bulbs (2)
CInsert Grow Bulbs into Lamp Hood
Briggs and stratton model 135232 user manual. Lamp Hood (bottom view)
Push straight in.
DO NOT TWIST BULBS!
Remember to replace Grow Bulbs every 6 months.
BInsert Lamp Arm into Base
Push | |
Lamp Arm | |
down until | Lamp Arm |
you hear | (back view) |
a “click.” |
Base
(back view)
DPlug Lamp Cord into Lamp Hood
Push Lamp Cord firmly into socket in Lamp Hood.
Lamp
Cord
E Place Lamp Hood | F Set Bowl into Base |
on Lamp Arm
Air Coupling
Center hands
over Lamp Arm | (back view) | (front view) |
and push Lamp | ||
Hood down | ||
until you hear a | Check to be sure that Bowl is | |
“click.” | ||
securely seated on Air Coupling in Base. |
G Moving Your AeroGarden6
Need Additional HELP?
For supplies and information, visit… www.aerogardensupport.com
Gently slide AeroGarden toward the surface edge and place other hand under Base.
H Place Your Garden
Under: A space that allows 22” (56cm) clearance for the full height of raised lamp
Page 1 Sprint User Guide A downloadable, printable guide to your Samsung Galaxy J3 Emerge and its features. Available applications and services are subject to change at any time. Page 2: Table Of Contents Table of Contents GETTING STARTED Introduction About the User Guide Get Support from Sprint Zone Set Up Your Phone Parts and Functions Battery Use Insert the Battery Remove the Battery. User manual for samsung galaxy j3 emerge.
On: A sturdy, watertolerant surface
(Metal surfaces may cause noise due to vibration)
In: A 60-75°F (16-24°C) environment
(optimal)
Near: A standard electrical outlet, per local regulations
68°F/20°C
Note: Do not place beneath under-cabinet lights.
Away From
Reach of children and pets
Lpg cellu m6 integral user manual. By professionals who have been specially trained by LPG Systems how to use it and is not suitable for use at home. OPERATING PRINCIPES: The operating principles of the medical device CELLU M6 Alliance® Medical consist of a suction force coupled with movements of rolls / valves, performed with treatment heads. Tion – even in part – is prohibited. All the illustrations in this operator’s manual are non-binding. Package contents Table of contents! Unpacking instructions to be retained. The package contents are identical, except for the Cellu M6 Keymodule i device, the face heads are not available on this version. 4 5. One Cellu M6 Keymodule 2. The operating principles of the medical device CELLU M6® Alliance Medical consist of a suction force coupled with movements of rolls / valves, performed with treatment heads. These heads are placed on the healthy skin of the patient and then moved across the area to be treated by the professional who has been trained by LPG Systems.
Direct sources of heat (e.g., stove, furnace vents)
Direct sources of cold air (e.g., window drafts, A/C vents)
For Optimal Tending & Harvesting, Also Consider
Easy access to un-softened water
2 Planting Your Garden
A Add Water Using a Spouted Container
Use room temperature municipal tap, bottled or purified water. Do not use well or softened water.
Lift
View Door
Fill to “Fill To Here”
(located inside Bowl)
When additional water is needed, “Water Low” light on Control Panel will blink. Add water to raise level up to “Fill To Here” inside Bowl.
It is okay to add water up to “Fill To Here” before “Water Low” light blinks.
Amount of
Water To Be
Added:
3.5quarts or..
3.2liters
B Plan Your Garden Layout
For best results plant Seed Pods labeled… ”Tall” – in Back openings (see diagram below) ”Medium” – in Side openings
”Short” – in Front openings
Back | |
Genovese Basil | |
(Sprouts in 3-7 days) | |
Tall | |
Side | Side |
Use height information on Seed Pod | |
Label to decide where to place each | |
Seed Pod in Grow Surface. | |
Note: Location of Seed Pod in Grow Surface does | |
not matter if all plants are the same height. | Front |
C Plant Your Garden
If you are planting…
Herbs or Flowers* - arrange Seed Pods by plant height (see “Plan Your Garden Layout” on page 5).
Tomatoes or Peppers (6-pod Vegetable Series Kits) - place one Seed Pod in each Front/Side opening and one Seed Pod in the center Back opening. Place Plant Spacers in remaining openings.
Green Beans, Salad Greens or Live Plants - place Seed/Plant Pods anywhere in Grow Surface.
Master Gardener Kit* - arrange Pods in Grow Surface according to plant height.
*Re-arranging may be required as plants grow.
Create a Custom Garden – combine two 3-pod Seed Kits.
Important guidelines to consider when combining Seed Kits…
•Only combine kits from the same Series, e.g., flower with flower, herb with herb, etc.
•Consider plant height when combining Seed Pods from two 3-pod Seed Kits. Refer to “Plan Your Garden Layout” on page 5 when deciding where to place Seed Pods in your 6-pod AeroGarden.
•When planting – use BOTH Starting Nutrients (two tablets) from each 3-pod Seed Kit.
•All Other Feedings – use TWO Growing Nutrients (two tablets) from each Seed Kit until they are gone.
Plant your AeroGarden. Check to see that…
• A Seed/Plant Pod or Plant Spacer is in each Grow Surface opening.
•Seed Pod Labels are facing forward.
•Seed Pods are pressed firmly in place.
Seed Pod | Grow Surface |
Bio-Domes™
Nutrients
Seed Kit Tray
D Place Bio-Domes™on Seed Pods
Place a Bio-Dome on each Seed Pod.
Press Bio-Domedown | Bio-Dome | Note: Do not remove Bio-Domesuntil |
until its rim almost | seeds have sprouted. NEVER | |
touches Grow Surface. | REMOVE SEED POD LABELS. |
E Add Starting Nutrient Tablets and Record Planting Date
Record Planting Date
Record the date your Seed/Plant Kit was planted on front cover of the Tending & Harvesting Guide.
Add 2 “Starting Nutrients”* directly into Bowl.
See 'Add Nutrients' (Feed Garden - Basic Feeding) on page 11 of this guide for additional feeding instructions.
*When combining two 3-pod Seed Kits, be sure to use 2 nutrient tablets when feeding your Garden (see “Create a Custom Garden” on page 6).
3 Starting Your Garden
A Plug Cord into Electrical Outlet
Plug in
View Door
What will happen..
1A green light on Control Panel will illuminate.
2Grow Bulbs will come on.
Look under Lamp Hood to check that both bulbs are lit.
If not, check to see if:
•Grow Bulbs are properly inserted in Lamp Hood (page 2, step 1C).
•Lamp Cord is plugged into Lamp Hood (page 2, step 1D).
•You are getting power through the electrical outlet.
3Air bubbles should be visible inside Bowl. If not, check to see if:
•Bowl is securely seated on Air Coupling in Base (see page 3, step 1F).
•Bowl has water up to “Fill To Here.”
3 Starting Your Garden (continued)
B Select Setting
Press the SELECT button until you reach the type of plant you are growing (Vegetables, Salad Greens, etc.).
Herbs | |
Salad | Flowers |
Greens | |
Add Nutrients | Water Low |
Replace | |
Live Plants |
Note: Depending on the plant type selected, your AeroGarden 6 lights will automatically turn on and off at pre-programmed intervals.
C Your Light Timer
Your Light Timer is Set To Start | |
1 | |
Growing Your Plants..Starting Now! |
If You Would Like to Change the Time
2 of Day Your Lights Will Go Off..
See “PersonalizeYour LightTimer” on page 10.
•Your lights will stay on for about 16 hours and will shut off for about 8 hours.
•Your lights will come on every day at the time you plugged in your AeroGarden 6.
Your AeroGarden 6 has lights and a built-in timer that automatically provide plants with the optimal amount of “sunlight”
(about 16 hours) and “night” (about 8 hours), depending on plant type you selected.
As long as plants get this amount of light, it does not matter when lights are turned off.* Many people find it convenient to have lights go on in the morning and off at night to match their own wake and sleep schedule.
*The exceptions to this are Flower & Vegetable plants. They require a daily dark period in order to produce flowers. If your plants will receive any room light during the day (natural or artificial), we recommend setting your AeroGarden lights to be on during the day.
5 Simple Steps..
In order to make this as simple as possible, you only need to set the time you want your AeroGarden
lights to go off (Off Time) and your built-in light timer automatically sets the On Time..nothing more for you to do.
Do the following to set the time you want your lights to go off:
1Decide what time you want the lights to go OFF.
2AT THAT TIME check that lights are on. If they are off, quickly press “Lights” button and immediately release. (Lights must be on in order to reset timer.)
3With lights on, press and hold “Lights” button until light next to the plant type you selected starts blinking – about 5 seconds.
4Release the button.
5When blinking stops (about 9 seconds), the lights will go off and your lights are now set to go off at this time every day.
You can reset your timer as often as you want.
Herbs | ||
Salad | Flowers | |
Add Nutrients | Greens | Water Low |
Replace | Lights Button | |
Bulbs | Vegetables | Live Plants |
Blinking Light (if you selected Salad Greens)
In case of power failure, your AeroGarden 6 has a backup system that stores light, nutrient & replace bulbs timers as well as plant selection settings. When power is restored, your AeroGarden will go back to the Off-On cycle you have set.
AeroGarden6 Control Panel
• Select
The number of hours lights are on and off depends on which plant type is selected.
• Lights On/Off
Use to occasionally override built-in light timer. Once pushed, lights will stay off/on until the next time built-in light timer is set to go on/off. This will not affect the timing of your light cycle, and occasional use of this feature will not harm your plants.
Add Nutrients
Replace
Bulbs
• Add Nutrients
(Feed Garden - Basic Feeding)
When “Add Nutrients” and “Water Low” lights start blinking (every 2 weeks), add 2 nutrient tablets* and fill the Bowl with water up to “Fill to Here.” Press and release “Reset” button to restart nutrient timer and turn off blinking lights.
*See Tending & Harvesting Guide for plant-specific nutrient information.
Herbs | |
Salad | Flowers |
Greens | Water Low |
Vegetables | Live Plants |
• Replace Bulbs†
When light blinks (after 6 months of use), it is time to replace Grow Bulbs. Bulbs can be ordered at www.aerogardensupport.com or from your retailer. After replacing Grow Bulbs, press “Reset” button to restart grow bulb timer and turn off flashing light.
NOTE: If you store your AeroGarden 6 between uses, grow bulb timer automatically stops when Garden is unplugged.
†See complete replacement instructions on next page.
• Water Low
When light blinks add water up to “Fill To Here.”
• Remove Bio-Domes
When plants appear through hole in
Seed Pod Label, remove Bio-Dome and discard or recycle.
NOTE: Never remove Seed Pod Labels.
Raise Lamp Hood (Lights)
As plants grow to 1-2” from lights, raise Lamp Arm one Locking Button at a time. Be sure Lamp Arm is set on the lowest Locking Button when starting your AeroGarden 6.
2Raise Lamp Arm/Lamp Hood by holding Lamp Arm & Hood with one hand, and pushing in
Locking Button with the other.
Push Locking
Button in
Replace Grow Bulbs – Order bulbs at www.aerogardensupport.com
Add Nutrients
Replace
Bulbs
Early Grow Bulb Replacement
When “Replace Bulbs” light on Control Panel begins blinking after 6 months of use…
•Unplug AeroGarden 6.
Aerogarden Model 100710 Blk
•Remove old Grow Bulbs and carefully discard.*
IMPORTANT: To avoid burning, be sure Grow Bulbs are cool before handling.
•Insert new Grow Bulbs into Lamp Hood.
•Plug in AeroGarden 6 and press and release “Reset” button to restart grow bulb timer.
If you replace Grow Bulbs before “Replace Bulbs” light illuminates, be sure to restart grow bulb timer as follows:
•Press and hold “Lights” button until light next to your selected plant type starts blinking – about 5 seconds.
•Release “Lights” button. The plant type selected light will continue to blink for about 9 seconds. While plant light is still blinking…
•Quickly press and release “Reset” button. “Replace Bulbs” light will blink once and the plant selected light will stop blinking.
*Check with local recycling authorities for light bulb recycling availability in your area.
Cleaning Instructions for your AeroGarden
Use only water and mild soap when cleaning your AeroGarden (except when Sanitizing - Step 6). Do not use abrasive cleaners or run through the dishwasher.
When your garden has completed its growing cycle…
1Unplug AeroGarden.
2Carefully remove Bowl and Grow Surface from Base and bring to
a sink. Set Base and Lamp Hood aside.
NEVER SUBMERSE BASE AND
CONTROL PANEL IN WATER.
3Remove Grow Surface from Bowl and place on a counter near a sink.
4Empty contents of Bowl in sink.
5Remove Seed Pods and plants from Grow Surface.
•Pull Seed Pods out of Grow Surface openings.
•Throw away Seed Pods and plant debris (plant growth and roots). If you compost, plant debris can be composted.
6Sanitize AeroGarden.
•Fill Bowl ¾ full with water.
•Add ¼ cup (59ml) of chlorine bleach.
•Let sit for 2 minutes.
•Using sanitizing water, wipe
Grow Surface and Bowl with soft cloth or sponge.*
*Gloves recommended.
•Scrub underside of Grow Surface with soft scrub brush to remove any tangled roots.
•Empty bleach water from Bowl.
7Rinse Bowl and Grow Surface with tap water. Repeat.
8Towel dry Bowl and Grow Surface before putting them back together and setting them on Base.
9If Grow Bulbs have been in use more than 6 months, they should be replaced at this time (see page 12).
Your AeroGarden is now ready for replanting.
13
Replanting Your AeroGarden
If you have already grown a garden in your AeroGarden 6, please follow the instructions below to reset the nutrient timer:
•Press and hold “Reset” button until red “Add Nutrients” light blinks 3 or 4 times (about 9 seconds).
•Release “Reset” button. “Add Nutrients” light will turn off.
•Your AeroGarden is now reset. (In some cases you may see other lights blink as well. This is nothing to worry about.)
NOTE: These steps do not reset grow bulb timer.
Herbs | ||
Salad | Flowers | |
Add Nutrients | Greens | Water Low |
Replace | ||
Bulbs | Vegetables | Live Plants |
Reset
Add Nutrients
Remember to..
•Replace Grow Bulbs after 6 months of use. Grow Bulbs can be ordered at www.aerogardensupport.com or from your retailer.
•Sanitize AeroGarden 6 before replanting (see page 13).
•Set your Lamp Hood to lowest position when starting a new garden.
!Bundle cord when furnishing is not in use.
U.S. CAUTION – You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; or, Consult the dealer or an experienced radio/TV technician for help.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER UN CHOC ÉLECTRIQUE, PRÉSENTER LA LAME LARGE À LA FENTE LARGE ET POUSSER JUSQU’AU FOND.
© 2008 AeroGrow International, Inc., Boulder, CO U.S.A. U.S. Patents Pending
5/9/08
To continue the download you need to go through the captcha: